Grease Filters

Flame Gard is a registered Trademark of Component Hardware, Registered in the U.S.

9 Item(s)

Set Descending Direction
per page

Grid  List 

Flame Gard® Type I Spark Arrestor Frame Baffle Grease Filters

Flame Gard® TYPE I Spark Arrestor Frame Baffle Grease Filters

Starting at: $92.00

Mfg : Flame Gard®

Model No. : 15xxxx

eRestaurantParts No.: 40040-40068

Units : Each

  • Flame Gard® Type 1 Spark Arrestor Frame Baffle Grease Filters
  • Made from all steel construction with a non-loading PTFE (Teflon) coat
  • Low static pressure
  • Grease Filter Type - Standard fixed baffle filter
  • Meets #96 N.F.P.A. requirements for cooking with solid fuel
  • The 3/8" x 1/2" Spark Arrestor screen meets requirement #211 of N.F.P.A. for solid fuel burning appliances
  • 94% efficient at grease extraction
  • Choose from various sizes above
  • Baffles should always run up and down (Vertical) while installing Grease Filters to allow the grease to run down the baffles to the grease trough and then to the collection cup
  • Measurements listed above are Height x Width x Thickness
  • U.L.C. Listed
PTFE Coated Baffles help the extraction of grease much more effectively. In the same manner that grease rolls off a PTFE coated pan, it rolls down the baffles, out of the filter and into the hood's remote collection cup. Because Flame Gard's® filters retain only insignificant amounts of surface grease and do not load, you will have a consistency of air flow throughout your operating day. In addition, Flame Gard's® filters can be easily cleaned in a pot sink or dishwasher with simple detergent and hot water. Learn More

Flame Gard® TYPE II Heavy Duty Stainless Steel Baffle Grease Filters

Flame Gard® TYPE II Heavy Duty Stainless Steel Baffle Grease Filters

Starting at: $93.75

Mfg : Flame Gard®

Model No. : 20xxxx

eRestaurantParts No.: 40070-40092

Units : Each

  • Flame Gard® Type II Heavy-Duty Stainless Steel Baffle Grease Filters
  • These grease filters provide a positive flame barrier protection with its heavy duty dual action Stainless Steel
  • Highly efficient in grease removal
  • Meets N.F.P.A #96 requirements by providing sturdy drop down handles on either side of the filter
  • Baffles should always run up and down (Vertical) when installing Grease Filters
  • Sizes above are listed as Height x Width x Thickness
  • NSF Certified
  • C.U.L. Listed
Learn More

Flame Gard® TYPE III Stainless Steel Baffle Grease Filters

Flame Gard® TYPE III Stainless Steel Baffle Grease Filters

Starting at: $48.00

Mfg : Flame Gard®

Model No. : 30xxxx

eRestaurantParts No.: 40096-40122

Units : Each

  • Flame Gard® TYPE III Stainless Steel Baffle Grease Filters
  • Standard duty Stainless Steel Baffle Filter
  • This grease filter provides a unique frame-less design that maximizes the free area
  • Meets requirements N.F.P.A #96
  • Low Static Pressure
  • Grease Filters should be measured and installed with the Baffles running up and down (Vertical)
  • Sizes above are listed as Height x Width x Thickness
  • C.U.L. Listed
Learn More

Flame Gard® Snap-On Filter Hooks for Flame Gard® Type VI Filters (Pair)

Snap-On Filter Hooks/Clips for Flame Gard® Type VI Filters (Pair)

$5.15

Mfg : Flame Gard®

Model No. : FR51-X015

eRestaurantParts No.: 40133

Units : Pair

These filter hooks simply clip onto the bottom of Flame Gard® Type VI Baffle Filters to retrofit them for CaptiveAire style hoods. Sold as a pair. Filter hooks snap onto the bottom of the filters and are held into place by the existing pop-rivets on the filter. Learn More

Flame Gard® Heavy Duty Mesh-Type Air Filters - Aluminum Framed F40

Flame Gard® Heavy Duty Mesh-Type Air Filters - Aluminum Framed

Starting at: $38.47

Mfg : Flame Gard®

Model No. : F40-xxxx

eRestaurantParts No.: 42112-42122

Units : Each

  • Aluminum Framed Heavy Duty Mesh Type Air Filter
  • Sizes above are listed as Height x Width (Height mm x Width mm)
  • Aluminum Framed - Rigid Heavy Duty Construction
  • Corrosion Resistant
  • All steel wire mesh design for maximum capture of dust and grease
  • Accepted for use by the city of New York Department of Building MEA #57-82M
Note: Nominal thickness is 2" (50mm). Actual thickness is 1-3/4" (45mm). Actual Height and Width are 7/16" (11mm) less than nominal sizes listed above. Learn More

FA51 Flame Gard® Type VI Aluminum Baffle Grease Filter

Flame Gard® Type VI Aluminum Baffle Grease Filters

Starting at: $18.82

Mfg : Flame Gard®

Model No. : FA51-xxxx

eRestaurantParts No.: 42140-42160

Units : Each

  • Aluminum, Flame Gard® Type VI Baffle Type Replacement Filter
  • The Manufacturer has replaced the old Grease Defender (FA30) Baffle filters with these new FA51 filters
  • Sturdy design with pop-riveted baffles
  • Sizes listed above are Height x Width (Height mm x Width mm)
  • Lightweight for ease of use
  • Safe, Dependable, Positive Flame Barrier Protection
  • Seamless, smooth surfaces permit constant grease run-off into hood collection troughs
  • All filters are supplied with Handles for easy install and removal
  • Grease Filters should be measured and installed with the Baffles running up and down (Vertical)
  • U.L. Tested & Classified
  • NSF Certified

Note: First two numbers of size indicate vertical height. Second two numbers represent horizontal width, both are nominal dimensions. Actual size of filters are 7/16" (11mm) less than nominal. Nominal thickness is 2" (50mm). Actual thickness is 1-3/4" (44mm).

Learn More

Flame Gard® Type VI Galvanized Baffle Grease Filter - FG51 - 4

Flame Gard® Type VI Galvanized Steel Heavy-Duty Baffle Grease Filters

Starting at: $18.17

Mfg : Flame Gard®

Model No. : FG51-xxxx

eRestaurantParts No.: 42212-42234

Units : Each

  • Flame Gard® Type VI Galvanized Baffle Grease Filter
  • Galvanized Steel for strong rugged performance, superb corrosion resistance and absolute low cost
  • Will not flex or twist like other filters
  • Safe, Dependable, Positive Flame Barrier Protection
  • Seamless, smooth surfaces permit constant grease run-off into hood collection troughs
  • Baffles are Pop-Riveted into place for a sturdy construction
  • Sizes above are listed as Height x Width
  • Grease Filters should be measured and installed with the Baffles running up and down (Vertical)
  • U.L. Tested & Classified
  • NSF Certified

Note: First numbers of size indicate vertical height. Second numbers represent horizontal width, both are nominal dimensions. Actual size of filters are 7/16" (11mm) less than nominal. Nominal thickness is 2" (50mm). Actual thickness is 1-3/4" (44mm).

Learn More

Flame Gard® Type VI Stainless Steel Baffle Grease Filters with Bright Finish FR51 FS50 _ 2

Flame Gard® Type VI Stainless Steel Baffle Grease Filters with Bright Finish

Starting at: $36.99

Mfg : Flame Gard®

Model No. : FR51-xxxx

eRestaurantParts No.: 99254

Units : Each

  • Flame Gard® Type VI Baffle Type Grease Filter - Replaces the old Grease Defender FS50 Stainless Steel Filters
  • Stainless Steel Filter with Stainless Steel Bright Finish
  • For tough commercial application and maximum permanent protection against rust and corrosion
  • Baffles Pop-Riveted into place for sturdier design
  • Easily cleaned by soaking, spraying or in conventional dishwashers
  • Grease Filters should be measured and installed with the Baffles running up and down (Vertical)
  • Sizes above are listed as Height x Width
  • U.L. Classified & Tested
  • NSF Certified
Note: First number of size indicate vertical height. Second number represent horizontal width, both are nominal dimensions. Actual size of filters are 1/2" less than nominal. Nominal thickness is 2" (50mm). Actual thickness is 1-3/4" (44mm). Learn More

Flame Gard® Type VI Stainless Steel Baffle Grease Filter with Hooks | 16" x 16"

Flame Gard® Type VI Stainless Steel Baffle Grease Filter with Hooks | 16" x 16"

$23.50

Mfg : Flame Gard®

Model No. : FR51-1616-H

eRestaurantParts No.: 99565

Units : Each

  • Flame Gard® Type VI Baffle Type Grease Filter with Hooks for Captive-Aire style hoods
  • Stainless Steel Filter with Stainless Steel Bright Finish; aesthetically pleasing for front of house installation
  • Stainless Steel construction for tough commercial application and maximum permanent protection against rust and corrosion
  • Smooth surfaces permit constant grease run-off into hood collection trough
  • Low static pressure ensures quiet operation
  • Grease Filters should be measured and installed with the Baffles running up and down (Vertical)
  • Safe, dependable flame barrier protection
  • Bail handles standard for easy installation and removal
  • Replaces Captive-Aire filter #A0010140
  • U.L. Classified & Tested
  • NSF Certified
Note: First number of size indicate vertical height. Second number represent horizontal width, both are nominal dimensions. Actual size of filters are 1/2" less than nominal. Nominal thickness is 2" (50mm). Actual thickness is 1-3/4" (44mm). Learn More

9 Item(s)

Set Descending Direction
per page

Grid  List