Kitchen Ventilation

Flame Gard is a registered Trademark of Component Hardware, Registered in the U.S.

Items 1 to 25 of 39 total

Set Descending Direction
per page

Grid  List 

Page:
  1. 1
  2. 2
Flame Gard® Type I Spark Arrestor Frame Baffle Grease Filters

Flame Gard® TYPE I Spark Arrestor Frame Baffle Grease Filters

Starting at: $92.00

Mfg : Flame Gard®

Model No. : 15xxxx

eRestaurantParts No.: 40040-40068

Units : Each

  • Flame Gard® Type 1 Spark Arrestor Frame Baffle Grease Filters
  • Made from all steel construction with a non-loading PTFE (Teflon) coat
  • Low static pressure
  • Grease Filter Type - Standard fixed baffle filter
  • Meets #96 N.F.P.A. requirements for cooking with solid fuel
  • The 3/8" x 1/2" Spark Arrestor screen meets requirement #211 of N.F.P.A. for solid fuel burning appliances
  • 94% efficient at grease extraction
  • Choose from various sizes above
  • Baffles should always run up and down (Vertical) while installing Grease Filters to allow the grease to run down the baffles to the grease trough and then to the collection cup
  • Measurements listed above are Height x Width x Thickness
  • U.L.C. Listed
PTFE Coated Baffles help the extraction of grease much more effectively. In the same manner that grease rolls off a PTFE coated pan, it rolls down the baffles, out of the filter and into the hood's remote collection cup. Because Flame Gard's® filters retain only insignificant amounts of surface grease and do not load, you will have a consistency of air flow throughout your operating day. In addition, Flame Gard's® filters can be easily cleaned in a pot sink or dishwasher with simple detergent and hot water. Learn More

Flame Gard® TYPE II Heavy Duty Stainless Steel Baffle Grease Filters

Flame Gard® TYPE II Heavy Duty Stainless Steel Baffle Grease Filters

Starting at: $93.75

Mfg : Flame Gard®

Model No. : 20xxxx

eRestaurantParts No.: 40070-40092

Units : Each

  • Flame Gard® Type II Heavy-Duty Stainless Steel Baffle Grease Filters
  • These grease filters provide a positive flame barrier protection with its heavy duty dual action Stainless Steel
  • Highly efficient in grease removal
  • Meets N.F.P.A #96 requirements by providing sturdy drop down handles on either side of the filter
  • Baffles should always run up and down (Vertical) when installing Grease Filters
  • Sizes above are listed as Height x Width x Thickness
  • NSF Certified
  • C.U.L. Listed
Learn More

Flame Gard® TYPE III Stainless Steel Baffle Grease Filters

Flame Gard® TYPE III Stainless Steel Baffle Grease Filters

Starting at: $48.00

Mfg : Flame Gard®

Model No. : 30xxxx

eRestaurantParts No.: 40096-40122

Units : Each

  • Flame Gard® TYPE III Stainless Steel Baffle Grease Filters
  • Standard duty Stainless Steel Baffle Filter
  • This grease filter provides a unique frame-less design that maximizes the free area
  • Meets requirements N.F.P.A #96
  • Low Static Pressure
  • Grease Filters should be measured and installed with the Baffles running up and down (Vertical)
  • Sizes above are listed as Height x Width x Thickness
  • C.U.L. Listed
Learn More

Flame Gard® Snap-On Filter Hooks for Flame Gard® Type VI Filters (Pair)

Snap-On Filter Hooks/Clips for Flame Gard® Type VI Filters (Pair)

$5.15

Mfg : Flame Gard®

Model No. : FR51-X015

eRestaurantParts No.: 40133

Units : Pair

These filter hooks simply clip onto the bottom of Flame Gard® Type VI Baffle Filters to retrofit them for CaptiveAire style hoods. Sold as a pair. Filter hooks snap onto the bottom of the filters and are held into place by the existing pop-rivets on the filter. Learn More

Flame Gard® 8" x 8" Flat Access Door

Flame Gard® 8" x 8" Flat Access Door

$70.00

Mfg : Flame Gard®

Model No. : 750606

eRestaurantParts No.: 40192

Units : Each

  • Flame Gard® UL Fire Rated Flat Access Door
  • Heavy-Duty 16 gauge steel construction
  • Back frame reinforces duct cut-out
  • Gasket rated to 2300°F (1200°C) for fire tight seal
  • Easy to install and easy to clean
  • Back Frame Dimensions: 8" x 8"
  • Front Panel Dimensions: 8" x 8"
  • Panel Width: Flat
  • Stud Height: 1"
  • Hole Size (Back Frame Inside Dimensions): 6" x 6"
  • Mounting Studs: 4
Learn More

Flame Gard® 10" x 10" Flat Access Door

Flame Gard® 10" x 10" Flat Access Door

$65.00

Mfg : Flame Gard®

Model No. : 750707

eRestaurantParts No.: 40196

Units : Each

  • Flame Gard® UL Fire Rated Flat Access Door
  • Heavy-Duty 16 gauge steel construction
  • Back frame reinforces duct cut-out
  • Gasket rated to 2300°F (1200°C) for fire tight seal
  • Easy to install and easy to clean
  • Back Frame Dimensions: 10" x 10"
  • Front Panel Dimensions: 10" x 10"
  • Panel Width: .5"
  • Stud Height: 1"
  • Hole Size (Back Frame Inside Dimensions): 7" x 7"
  • Mounting Studs: 4
Learn More

Flame Gard® 7" x 10" Flat Access Door

Flame Gard® 7" x 10" Flat Access Door

$65.00

Mfg : Flame Gard®

Model No. : 750710

eRestaurantParts No.: 40198

Units : Each

  • Flame Gard® UL Fire Rated Flat Access Door
  • Heavy-Duty 16 gauge steel construction
  • Back frame reinforces duct cut-out
  • Gasket rated to 2300°F (1200°C) for fire tight seal
  • Easy to install and easy to clean
  • Back Frame Dimensions: 7" x 10"
  • Front Panel Dimensions: 7" x 10"
  • Panel Width: Flat
  • Stud Height: 1"
  • Hole Size (Back Frame Inside Dimensions): 5.5" x 7.5"
  • Mounting Studs: 4
Learn More

Flame Gard® 10" x 15" Flat Access Door

Flame Gard® 10" x 15" Flat Access Door

$80.00

Mfg : Flame Gard®

Model No. : 750712

eRestaurantParts No.: 40200

Units : Each

  • Flame Gard® UL Fire Rated Flat Access Door
  • Heavy-Duty 16 gauge steel construction
  • Back frame reinforces duct cut-out
  • Gasket rated to 2300°F (1200°C) for fire tight seal
  • Easy to install and easy to clean
  • Back Frame Dimensions: 10" x 15"
  • Front Panel Dimensions: 10" x 15"
  • Panel Width: .5"
  • Stud Height: 1"
  • Hole Size (Back Frame Inside Dimensions): 7" x 12"
  • Mounting Studs: 4
Learn More

Flame Gard® 7" x 15" Flat Access Door

Flame Gard® 7" x 15" Flat Access Door

$80.00

Mfg : Flame Gard®

Model No. : 750715

eRestaurantParts No.: 40202

Units : Each

  • Flame Gard® UL Fire Rated Flat Access Door
  • Heavy-Duty 16 gauge steel construction
  • Back frame reinforces duct cut-out
  • Gasket rated to 2300°F (1200°C) for fire tight seal
  • Easy to install and easy to clean
  • Back Frame Dimensions: 7" x 15"
  • Front Panel Dimensions: 7" x 15"
  • Panel Width: Flat
  • Stud Height: 1"
  • Hole Size (Back Frame Inside Dimensions): 5.5" x 13.5"
  • Mounting Studs: 6
Learn More

Flame Gard® 10" x 23" Flat Access Door

Flame Gard® 10" x 23" Flat Access Door

$97.25

Mfg : Flame Gard®

Model No. : 750720

eRestaurantParts No.: 40204

Units : Each

  • Flame Gard® UL Fire Rated Flat Access Door
  • Heavy-Duty 16 gauge steel construction
  • Back frame reinforces duct cut-out
  • Gasket rated to 2300°F (1200°C) for fire tight seal
  • Easy to install and easy to clean
  • Back Frame Dimensions: 10" x 23"
  • Front Panel Dimensions: 10" x 23"
  • Panel Width: .5"
  • Stud Height: 1"
  • Hole Size (Back Frame Inside Dimensions): 7" x 20"
  • Mounting Studs: 10
Learn More

Flame Gard® 7" x 23" Flat Access Door

Flame Gard® 7" x 23" Flat Access Door

$97.25

Mfg : Flame Gard®

Model No. : 750723

eRestaurantParts No.: 40206

Units : Each

  • Flame Gard® UL Fire Rated Flat Access Door
  • Heavy-Duty 16 gauge steel construction
  • Back frame reinforces duct cut-out
  • Gasket rated to 2300°F (1200°C) for fire tight seal
  • Easy to install and easy to clean
  • Back Frame Dimensions: 7" x 23"
  • Front Panel Dimensions: 7" x 23"
  • Panel Width: Flat
  • Stud Height: 1"
  • Hole Size (Back Frame Inside Dimensions): 5.5" x 21.5"
  • Mounting Studs: 10
Learn More

Flame Gard® 15" x 15" Flat Access Door

Flame Gard® 15" x 15" Flat Access Door

$89.00

Mfg : Flame Gard®

Model No. : 751212

eRestaurantParts No.: 40212

Units : Each

  • Flame Gard® UL Fire Rated Flat Access Door
  • Heavy-Duty 16 gauge steel construction
  • Back frame reinforces duct cut-out
  • Gasket rated to 2300°F (1200°C) for fire tight seal
  • Easy to install and easy to clean
  • Back Frame Dimensions: 15" x 15"
  • Front Panel Dimensions: 15" x 15"
  • Panel Width: .5"
  • Stud Height: 1"
  • Hole Size (Back Frame Inside Dimensions): 12" x 12"
  • Mounting Studs: 8
Learn More

Flame Gard® 15" x 23" Flat Access Door

Flame Gard® 15" x 23" Flat Access Door

$115.00

Mfg : Flame Gard®

Model No. : 751220

eRestaurantParts No.: 40214

Units : Each

  • Flame Gard® UL Fire Rated Flat Access Door
  • Heavy-Duty 16 gauge steel construction
  • Back frame reinforces duct cut-out
  • Gasket rated to 2300°F (1200°C) for fire tight seal
  • Easy to install and easy to clean
  • Back Frame Dimensions: 15" x 23"
  • Front Panel Dimensions: 15" x 23"
  • Panel Width: .5"
  • Stud Height: 1"
  • Hole Size (Back Frame Inside Dimensions): 12" x 20"
  • Mounting Studs: 12
Learn More

Flame Gard® 19" x 23" Flat Access Door

Flame Gard® 19" x 23" Flat Access Door

$125.00

Mfg : Flame Gard®

Model No. : 751620

eRestaurantParts No.: 40218

Units : Each

  • Flame Gard® UL Fire Rated Flat Access Door
  • Heavy-Duty 16 gauge steel construction
  • Back frame reinforces duct cut-out
  • Gasket rated to 2300°F (1200°C) for fire tight seal
  • Easy to install and easy to clean
  • Back Frame Dimensions: 19" x 23"
  • Front Panel Dimensions: 19" x 23"
  • Panel Width: .5"
  • Stud Height: 1"
  • Hole Size (Back Frame Inside Dimensions): 16" x 20"
  • Mounting Studs: 12
Learn More

Flame Gard® 23" x 23" Flat Access Door

Flame Gard® 23" x 23" Flat Access Door

$125.00

Mfg : Flame Gard®

Model No. : 752020

eRestaurantParts No.: 40222

Units : Each

  • Flame Gard® UL Fire Rated Flat Access Door
  • Heavy-Duty 16 gauge steel construction
  • Back frame reinforces duct cut-out
  • Gasket rated to 2300°F (1200°C) for fire tight seal
  • Easy to install and easy to clean
  • Back Frame Dimensions: 23" x 23"
  • Front Panel Dimensions: 23" x 23"
  • Panel Width: .5"
  • Stud Height: 1"
  • Hole Size (Back Frame Inside Dimensions): 20" x 20"
  • Mounting Studs: 16
Learn More

Out of stock

Direct to Duct Hi-Temp Access Doors ACC-10x6 ACC-12X8 ACC-18X14

Direct to Duct Hi-Temp Access Doors

Starting at: $68.52

Mfg : Flame Gard®

Model No. : ACC-xxXxx

eRestaurantParts No.: 40576-40584

Units : Each

  • Hi-Temp Access Doors designed to be used direct to the duct
  • Hi-Temp Access Door is solid, leak resistant and consists of two layers of stamped, hot dipped galvanized steel and one 16 gauge black iron backing plate
  • Hi-Temperature ceramic fiber gasket (2300°F, 1260°C Max)
  • Meets NFPA 96 Standards
  • Gasket is permanently bonded to the outside panel of the access door to eliminate leakage
  • Zinc plated conical springs are installed, between the inner and outer plates, to facilitate opening
  • Zinc coated wing nuts are easily turned by hand
  • No measuring (self-adhesive template provided)
Learn More

Nickel Plated Brass Canopy Hood Drain

Nickel Plated Brass Canopy Hood Drain

$11.62

Mfg : Flame Gard®

Model No. : F10-1187

eRestaurantParts No.: 42094

Units : Each

  • Designed for draining grease from trough to grease cup
  • Supplied with locknut and washer
  • Fits 1/2”(13mm) I.D Hose or 3/8”(9.5mm) O.D
Learn More

Stainless Steel Canopy Hood Side Mount Grease Cup

Stainless Steel Canopy Hood Side Mount Grease Cup

$9.65

Mfg : Flame Gard®

Model No. : F15-0019

eRestaurantParts No.: 42096

Units : Each

  • Removable stainless steel canopy hood side mount grease cup
  • Conforms to N.F.P.A. requirements
  • Size: 4-1/2 x 6-3/4" x 2-1/2" deep (110mm x 171mm x 63mm)
  • Type 304 Stainless Steel
  • 1/9 pan equivalent on all models
Learn More

2-1/2" Deep Stainless Steel Canopy Hood Keyhole Mount Grease Cup

2-1/2" Deep Stainless Steel Canopy Hood Keyhole Mount Grease Cup

$11.85

Mfg : Flame Gard®

Model No. : F15-2500

eRestaurantParts No.: 42098

Units : Each

  • Removable stainless steel canopy hood keyhole mount grease cup
  • Conforms to N.F.P.A. requirements
  • Size: 4 x 6-5/8" x 2-1/2"deep(100mm x 168mm x 100mm)
  • Type 304 Stainless Steel
Learn More

4” Deep Stainless Steel Canopy Hood Keyhole Mount Grease Cup

4” Deep Stainless Steel Canopy Hood Keyhole Mount Grease Cup

$22.61

Mfg : Flame Gard®

Model No. : F15-4000

eRestaurantParts No.: 42104

Units : Each

  • Removable stainless steel canopy hood keyhole mount grease cup
  • Conforms to N.F.P.A. requirements
  • Size: 4" x 6-5/8" x 4" deep (100mm x 168mm x 100mm)
  • Type 304 Stainless Steel
Learn More

Flame Gard® Heavy Duty Mesh-Type Air Filters - Aluminum Framed F40

Flame Gard® Heavy Duty Mesh-Type Air Filters - Aluminum Framed

Starting at: $38.47

Mfg : Flame Gard®

Model No. : F40-xxxx

eRestaurantParts No.: 42112-42122

Units : Each

  • Aluminum Framed Heavy Duty Mesh Type Air Filter
  • Sizes above are listed as Height x Width (Height mm x Width mm)
  • Aluminum Framed - Rigid Heavy Duty Construction
  • Corrosion Resistant
  • All steel wire mesh design for maximum capture of dust and grease
  • Accepted for use by the city of New York Department of Building MEA #57-82M
Note: Nominal thickness is 2" (50mm). Actual thickness is 1-3/4" (45mm). Actual Height and Width are 7/16" (11mm) less than nominal sizes listed above. Learn More

FA51 Flame Gard® Type VI Aluminum Baffle Grease Filter

Flame Gard® Type VI Aluminum Baffle Grease Filters

Starting at: $18.82

Mfg : Flame Gard®

Model No. : FA51-xxxx

eRestaurantParts No.: 42140-42160

Units : Each

  • Aluminum, Flame Gard® Type VI Baffle Type Replacement Filter
  • The Manufacturer has replaced the old Grease Defender (FA30) Baffle filters with these new FA51 filters
  • Sturdy design with pop-riveted baffles
  • Sizes listed above are Height x Width (Height mm x Width mm)
  • Lightweight for ease of use
  • Safe, Dependable, Positive Flame Barrier Protection
  • Seamless, smooth surfaces permit constant grease run-off into hood collection troughs
  • All filters are supplied with Handles for easy install and removal
  • Grease Filters should be measured and installed with the Baffles running up and down (Vertical)
  • U.L. Tested & Classified
  • NSF Certified

Note: First two numbers of size indicate vertical height. Second two numbers represent horizontal width, both are nominal dimensions. Actual size of filters are 7/16" (11mm) less than nominal. Nominal thickness is 2" (50mm). Actual thickness is 1-3/4" (44mm).

Learn More

Flame Gard® Type VI Galvanized Baffle Grease Filter - FG51 - 4

Flame Gard® Type VI Galvanized Steel Heavy-Duty Baffle Grease Filters

Starting at: $18.17

Mfg : Flame Gard®

Model No. : FG51-xxxx

eRestaurantParts No.: 42212-42234

Units : Each

  • Flame Gard® Type VI Galvanized Baffle Grease Filter
  • Galvanized Steel for strong rugged performance, superb corrosion resistance and absolute low cost
  • Will not flex or twist like other filters
  • Safe, Dependable, Positive Flame Barrier Protection
  • Seamless, smooth surfaces permit constant grease run-off into hood collection troughs
  • Baffles are Pop-Riveted into place for a sturdy construction
  • Sizes above are listed as Height x Width
  • Grease Filters should be measured and installed with the Baffles running up and down (Vertical)
  • U.L. Tested & Classified
  • NSF Certified

Note: First numbers of size indicate vertical height. Second numbers represent horizontal width, both are nominal dimensions. Actual size of filters are 7/16" (11mm) less than nominal. Nominal thickness is 2" (50mm). Actual thickness is 1-3/4" (44mm).

Learn More

Stainless Steel Cap Strip Bright Finish J63-1451-x

Stainless Steel Cap Strip Bright Finish

Starting at: $11.75

Mfg : Flame Gard®

Model No. : J63-1451-x

eRestaurantParts No.: 42529

Units : Each

  • Stainless Steel Cap Strip for 1/16" (1.5mm) Material - Bright Finish
  • Completely fabricated from Stainless Steel
  • Available in various lengths for minimal waste
  • New wider construction for ease of installation
  • Material is hemmed to provide safety when sealing the sheet with silicone
  • Exposed stainless is polished to a bright chome-like finish with grain matching the wall lining
  • Individually plastic sleeved for protection
  • Ideal support system for restaurant wall flashing installations
  • Choose from either 7ft., 8ft., 9ft., or 10ft. lengths above
Learn More

Stainless Steel Cap Strip 400 Series-Satin Finish J63-1651-xx

Stainless Steel Cap Strip 400 Series-Satin Finish

Starting at: $15.75

Mfg : Flame Gard®

Model No. : J63-1651-xx

eRestaurantParts No.: 42537

Units : Each

  • Stainless Steel Cap Strip for 1/16" (1.5mm) Material - 400 Series Satin Finish
  • Completely fabricated from Stainless Steel
  • Available in various lengths for minimal waste
  • New wider construction for ease of installation
  • Material is hemmed to provide safety when sealing the sheet with silicone
  • Exposed stainless is polished to satin finish with grain matching the wall lining
  • Individually plastic sleeved for protection
  • Ideal support system for restaurant wall flashing installations
  • Choose from either 6.5ft. or 10ft. lengths above. 10ft Lengths cannot be shipped UPS or FedEx and must go Common Carrier.
Learn More

Out of stock

Items 1 to 25 of 39 total

Set Descending Direction
per page

Grid  List 

Page:
  1. 1
  2. 2